跳至主要内容

Evaluation of Cathodic Arc Deposited Thick CrAlSiN Coatings by Erosion Test

Read  full  paper  at:
http://www.scirp.org/journal/PaperInformation.aspx?PaperID=53364#.VMBg0izQrzE

Author(s)  
Wei-Yu Ho, Yen-Sho Chang, Bo-Yi Chou, Chien-Liang Lin*

Affiliation(s)
Department of Materials and Energy Engineering, MingDao University, Changhua, Taiwan.

ABSTRACT
CrAlSiN with thickness up to 16 μm was deposited on tungsten carbide via multi-deposition process by cathode arc deposition technique. Scratch and water-sand jet impingement erosion tests were carried out to evaluate the adhesion by determining the worn surface of the coatings. Results showed that the failure mode of the adhesion can be concluded that the weak bond of each CrAlSiN layer as compared to the strong bond between the coating and substrate. The average surface roughness of the coatings before the erosion test was about the same level. After the erosion test of 30 minutes, the eroded CrAlSiN coatings exhibited improved average surface roughness as compared to the original CrAlSiN coatings. Further increasing the erosion up to 60 minutes, the wear and minor peeling of the CrAlSiN coating between each layer was observed. A further research to improve the bond strength between each layer was needed.

KEYWORDS
Cathodic Arc Evaporation, CrAlSiN Coating, Erosion

Cite this paper
Ho, W. , Chang, Y. , Chou, B. and Lin, C. (2015) Evaluation of Cathodic Arc Deposited Thick CrAlSiN Coatings by Erosion Test. Journal of Materials Science and Chemical Engineering, 3, 66-71. doi: 10.4236/msce.2015.31010.

References
[1]Van Stappen, M., De Bruyn, K., Quaeyhaegens, C., Stals, L. and Poulek, V. (1995) Deposition and Properties of Thick Corrosion and Wear-Resistant Ti2N Coatings. Surface and Coatings Technology, 74-75, 143-146. http://dx.doi.org/10.1016/0257-8972(95)08225-5
 
[2]Lang, F.Q. and Yu, Z.M. (2001) The Corrosion Resistance and Wear Resistance of Thick TiN Coatings Deposited by Arc Ion Plating. Surface and Coatings Technology, 145, 80-87. http://dx.doi.org/10.1016/S0257-8972(01)01284-1
 
[3]Zhao, S.-S., Du, H., Zheng, J.-D., Yang, Y., Wang, W., Gong, J. and Sun, C. (2008) Deposition of Thick TiAlN Coatings on 2024 Al/SiCp Substrate by Arc Ion Plating. Surface & Coatings Technology, 202, 5170-5174. http://dx.doi.org/10.1016/j.surfcoat.2008.05.041
 
[4]Lin, J.L., Sproul, W.D., Moore, J.J., Lee, S. and Myers, S. (2011) High Rate Deposition of Thick CrN and Cr2N Coatings Using Modulated Pulse Power (MPP) Magnetron Sputtering. Surface & Coatings Technology, 205, 3226-3234. http://dx.doi.org/10.1016/j.surfcoat.2010.11.039
 
[5]Gorokhovsky, V.I. (2010) Characterization of Thick Ceramic and Cermet Coatings Deposited by an Industrial-Scale LAFAD Process. Surface & Coatings Technology, 204, 1216-1221. http://dx.doi.org/10.1016/j.surfcoat.2009.10.027
 
[6]Lin, J.L., Sproul, W.D. and Moore, J.J. (2012) Tribological Behavior of Thick CrN Coatings Deposited by Modulated Pulsed Power Magnetron Sputtering. Surface & Coatings Technology, 206, 2474-2483. http://dx.doi.org/10.1016/j.surfcoat.2011.10.053
 
[7]Shi, P.Z., Wang, J., Tian, C.X., Li, Z.G., Zhang, G.D., Fu, D.J. and Yang, B. (2013) Structure, Mechanical and Tribological Properties of CrN Thick Coatings Deposited by Circular Combined Tubular Arc Ion Plating. Surface & Coatings Technology, 228, S534-S537. http://dx.doi.org/10.1016/j.surfcoat.2012.04.041
 
[8]Kim, S.K., Le, V.V., Vinh, P.V. and Lee, J.W. (2008) Effect of Cathode Arc Current and Bias Voltage on the Mechanical Properties of CrAlSiN Thin Films. Surface and Coatings Technology, 202, 5400-5404. http://dx.doi.org/10.1016/j.surfcoat.2008.06.019
 
[9]Tien, S.-K., Lin, C.-H., Tsai, Y.-Z. and Duh, J.-G. (2007) Effect of Nitrogen Flow on the Properties of Quaternary CrAlSiN Coatings at Elevated Temperatures. Surface and Coatings Technology, 202, 735-739. http://dx.doi.org/10.1016/j.surfcoat.2007.06.042
 
[10]Chang, Y.-Y., Chang, C.-P., Wang, D.-Y., Yang, S.-M. and Wu, W. (2008) High Temperature Oxidation Resistance of CrAlSiN Coatings Synthesized by a Cathodic Arc Deposition Process. Journal of Alloys and Compounds, 461, 336- 341. http://dx.doi.org/10.1016/j.jallcom.2007.06.084
 
[11]Polcar, T. and Cavaleiro, A. (2011) High-Temperature Tribological Properties of CrAlN, CrAlSiN and AlCrSiN Coatings. Surface and Coatings Technology, 206, 1244-1251. http://dx.doi.org/10.1016/j.surfcoat.2011.08.037
 
[12]Chen, H.-W., Chan, Y.-C., Lee, J.-W. and Duh, J.-G. (2010) Oxidation Behavior of Si-Doped Nanocomposite CrAlSiN Coatings. Surface and Coatings Technology, 205, 1189-1194. http://dx.doi.org/10.1016/j.surfcoat.2010.08.156
 
[13]Ding, X.-Z., Zeng, X.T. and Liu, Y.C. (2011) Structure and Properties of CrAlSiN Nanocomposite Coatings Deposited by Lateral Rotating Cathod Arc. Thin Solid Films, 519, 1894-1900. http://dx.doi.org/10.1016/j.tsf.2010.10.022
 
[14]Endrino, J.L., Palacín, S., Aguirre, M.H., Gutiérrez, A. and Sch?fers, F. (2007) Determination of the Local Environment of Silicon and the Microstructure of Quaternary CrAl(Si)N Films. Acta Materialia, 55, 2129-2135. http://dx.doi.org/10.1016/j.actamat.2006.11.014
 
[15]Chang, Y.-S., Ho, W.-Y., Tsou, P.-Y. and Lin, C.-L. (2014) Advanced Materials Research, 900, 517-521.
 
[16]López, D., Sánchez, C. and Toro, A. (2005) Corrosion-Erosion Behavior of TiN-Coated Stainless Steels in Aqueous Slurries. Wear, 258, 684-692. http://dx.doi.org/10.1016/j.wear.2004.09.015          eww150122lx
标签：

评论

发表评论

此博客中的热门博文

Does Immigration Promote the Investment of the Monopolistic Firm?

In the present paper, we examine the effect of increasing uncertainty of immigrants’ growth on the optimal timing of investment of a firm that has a monopolistic power over the labor market. It is revealed that when the uncertainty of immigrants’ growth is more than a threshold level, increasing uncertainty of immigrants’ growth accelerates the optimal timing of firms’ investment and enhances the economic growth, even if the uncertainty of immigrants’ growth is formulated by the geometric Brownian motion, which is in sharp contrast to the standard result that an increase in the uncertainty postpones the optimal timing. With an increase in the immigrants over the past ten years, workforces in the host countries have been growing significantly to the extent that the immigrants represent 70% of the increase in the workforce in Europe, and 47% in the United States as OECD indicates. In the present paper, we attempted to investigate the effect of increased uncertainty caused by the growi...
发表评论
阅读全文

Education Policy Implementation: A Mechanism for Enhancing Primary Education Development in Zanzibar

Education is one of the fundamental rights of individuals; therefore, the government of a country needs to develop and strengthen educational policy and quality as well as to ensure that everyone has equal access to basic education. The improvement of access and quality of education in the world is becoming as an essential factor in development, whereas the basic education (primary school), is acknowledged as a foundation of the higher educational development for every country. To fulfill this goal, governments introduce several policies and procedures; however, it requires some reforms and participation from the politician, policymakers, and other stakeholders to re-examine educational policy so that it can lead to multiplication and betterment of the reforms. Educational reforms actually focus on accountability. A positive educational development and reform is very challenging and needs more effort and strategy on how to use and utilize the resources effectively as such it can achie...
发表评论
阅读全文