跳至主要内容

An Analysis of Varnish and Impregnation Processes for Combustion Temperature of Scotch Pine

Read  full  paper  at:
http://www.scirp.org/journal/PaperInformation.aspx?PaperID=53291#.VLx7b8nQrzE

ABSTRACT
This study was performed to determine the effects of varnishing after impregnation with boron compounds on the combustion properties of Scotch pine. For this purpose, test samples prepared from Scotch pine (Pinus sylvestris Lipsky) wood were impregnated according to ASTM-D 1413-99 standard with boric acid (Ba) and borax (Bx) by vacuum technique. After impregnation, surfaces were coated by cellulosic (Cv), synthetic (Sn), polyurathane (Pu), waterborne (Wb), acrylic (Ac) and acid hardening (Ah) varnishes in accordance with ASTM D-3023 standard and then, combustion temperature was determined. According to material and process type, combustion temperature was the highest in Bx and Wb in flame source combustion (FSC), the lowest in Ba and Ac without flame source combustion (WFSC). According to combustion type, impregnation material and varnish type, combustion temperature was the highest in FSC, borax and cellulosic varnish combination and the lowest in WFSC, boric acid and acid hardening varnish combination. In conclusion, impregnation materials decrease while varnishes increase the combustion temperature of Scotch pine wood.
 
Cite this paper
Atar, M. , Döngel, N. and Çinar, H. (2015) An Analysis of Varnish and Impregnation Processes for Combustion Temperature of Scotch Pine. Materials Sciences and Applications, 6, 78-85. doi: 10.4236/msa.2015.61010.
 
References
[1]Bednarek, Z. and Kaliszuk-Wietecka, A. (2007) Analysis of Fire-Protection Impregnation Influence on Wood Strength. Journal of Civil Engineering Management, 13, 79-85.
 
[2]Goldstein, I.S. (1973) Deterioration and Protection of Wood from Thermal Attact: Wood Deteration and Its Prevention by Preservation Treatments. Syracuse University Press, Syracuse, 307-339.
 
[3]Levan, S.L. and Widany, J.E. (1990) Effects of Fire Retardant Treatments on Wood Strength: A Review. Wood and Fiber Science, 22, 113-131.
 
[4]Keskin, H., Atar, M. and Izciler, M. (2009) Impacts of Impregnation Chemicals on Combustion Properties of the Laminated Wood Materials Produced Combination of Beech and Poplar Veneers. Construction and Building Materials, 23, 634-643.
http://dx.doi.org/10.1016/j.conbuildmat.2008.02.006
 
[5]Yapici, F., Uysal, B., Kurt, S., Esen, R. and Ozcan, C. (2011) Impacts of Impreh-Gnation Chemicals on Finishing Process and Comcustion Properties of Oriental Beech (Fagus Orientalis L.) Wood. Bioresources, 6, 3933-3943.
 
[6]Evans, P.D., Michell, A.J. and Schmalzl, K. (1992) Studies of the Degradetion and Protection of Wood Surfaces. Wood Science and Technology, 26, 151-163.
http://dx.doi.org/10.1007/BF00194471
 
[7]Atar, M., Keskin, H. and Yavuzcan, H.G. (2004) Varnish Layer Hardness of Oriental Beech (Fagus orientalis Lipsky) Wood as Affected by Impregnation and Color Bleaching. Journal of Coatings Technology (JCT), 1, 498-504.
 
[8]Feist, W.C. (1988) Weathering of Wood and Its Control by Water Repellent Preservatives. In: Hamel, M.P., Ed., Wood Protection Techniques and the Use of Treated Wood in Construction, Forest Products Society, Madison, 82-88.
 
[9]Harrow, K.M. (1997) Leachibility of Some Water-Soluble Wood Preservatives, NZ. Wood Science Technology, B32, 33-40.
 
[10]Sell, J. and Feist, W.C. (1985) Weathering Behaviour of Cromium-Copper-Boron Treated Wood. Holz als Roh und Werkstoff, 43, 518.
http://dx.doi.org/10.1007/BF02608035
 
[11]TS 2476 (1976) Odunda Fiziksel ve Mekaniksel Deneyler Ì çin Numune Alma Metotlar? ve Genel Özellikler. T.S.E, Ankara.
 
[12]DYO (1996) Dewilux, Teknik Bülten. Dewilux Fabrikalar? A.S, Ìzmir.
 
[13]ASTM D-1413-99 (2005) Standart Method of Testing Wood Preservatives by Laboratory Soilblock Cultures. Annual Book of ASTM Standards, 452-460.
 
[14]ASTM D-3023 (1998) Standard Practice for Determination of Resistance of Factory Applied Coatings on Wood Products of Stain and Reagents. American Society for Testing and Materials.
 
[15]ASTM E-160-50 (1975) Standard Test Method for Combustible Properties of Treated Wood by the Cribe Test. ASTM, 04.07, 809-813.                                                                                                 eww150119lx
标签：

评论

发表评论

此博客中的热门博文

A Comparison of Methods Used to Determine the Oleic/Linoleic Acid Ratio in Cultivated Peanut (Arachis hypogaea L.)

Cultivated peanut ( Arachis hypogaea L.) is an important oil and food crop. It is also a cheap source of protein, a good source of essential vitamins and minerals, and a component of many food products. The fatty acid composition of peanuts has become increasingly important with the realization that oleic acid content significantly affects the development of rancidity. And oil content of peanuts significantly affects flavor and shelf-life. Early generation screening of breeding lines for high oleic acid content greatly increases the efficiency of developing new peanut varieties. The objective of this study was to compare the accuracy of methods used to classify individual peanut seed as high oleic or not high oleic. Three hundred and seventy-four (374) seeds, spanning twenty-three (23) genotypes varying in oil composition (i.e. high oleic (H) or normal/not high oleic (NH) inclusive of all four peanut market-types (runner, Spanish, Valencia and Virginia), were individually tested ...
发表评论
阅读全文

Location Optimization of a Coal Power Plant to Balance Costs against Plant’s Emission Exposure

Fuel and its delivery cost comprise the biggest expense in coal power plant operations. Delivery of electricity from generation to consumers requires investment in power lines and transmission grids. Placing a coal power plant or multiple power plants near dense population centers can lower transmission costs. If a coalmine is nearby, transportation costs can also be reduced. However, emissions from coal plants play a key role in worsening health crises in many countries. And coal upon combustion produces CO 2 , SO 2 , NO x , CO, Metallic and Particle Matter (PM10 & PM2.5). The presence of these chemical compounds in the atmosphere in close vicinity to humans, livestock, and agriculture carries detrimental health consequences. The goal of the research was to develop a methodology to minimize the public’s exposure to harmful emissions from coal power plants while maintaining minimal operational costs related to electric distribution losses and coal logistics. The objective was...
发表评论
阅读全文

Evaluation of the Safety and Efficacy of Continuous Use of a Home-Use High-Frequency Facial Treatment Appliance

At present, many home-use beauty devices are available in the market. In particular, many products developed for facial treatment use light, e.g., a flash lamp or a light-emitting diode (LED). In this study, the safety of 4 weeks’ continuous use of NEWA TM , a high-frequency facial treatment appliance, every alternate day at home was verified, and its efficacy was evaluated in Japanese individuals with healthy skin aged 30 years or older who complained of sagging of the facial skin.  Transepidermal water loss (TEWL), melanin levels, erythema levels, sebum secretion levels, skin color changes and wrinkle improvement in the facial skin were measured before the appliance began to be used (study baseline), at 2 and 4 weeks after it had begun to be used, and at 2 weeks after completion of the 4-week treatment period (6 weeks from the study baseline). In addition, data obtained by subjective evaluation by the subjects themselves on a visual analog scale (VAS) were also analyzed. Fur...
发表评论
阅读全文